跳至主要内容

Installation technique of 15 ton chain hoist

15 ton chain hoist is often used within a workshop to lifting tools, this kind of small volume, light weight, convenient installation, operation and lifting hoist are very stable, has begun to replace bulky type 15 ton hoist. Before buying the electric chain hoist, according to the following several points to identify the quality of electrical chain block. First of all, after turning on the power supply, control electric chain hoist to move around, observe if the direction key is correct, also pay attention to whether or not there is brake voice when stopped. And, check whether the chain is down or not after stopping, if there is, that means the sheet is too loose, or is not installed properly. If these no problem, click on the button to up and down, observe the running distance, the smaller the 15 ton hoist run, the better. In some factory or workshop, sometimes need to run relatively small distance. Such as installing or docking, need 15 ton hoist rise or fall slowly, to facilitate calibration and installation, but electrical chain block is mostly single speed, even double speed is not slow enough to meet the requirement of installation speed. In this case, it need click stop to make the running time very short, so the moving range is relatively small, and can calibrate in each time point, until the equipment installation is complete. This is reason of why in the choice of 15 ton chain hoist need to click stop to check the lifting distance, in principle, the smaller the lifting distance is, the better.

评论

此博客中的热门博文

How to deal with 3 ton electric chain hoist motor overheating

Any machine has the cycle and time of operation, is not suitable for a long time continuous operation. Long time operation will cause mechanical damage and even accidents, but in general if the 3 ton electric chain hoist surface temperature is too high, we need to check what is the reason. Firstly to check whether it is because the electric hoist weight is too large, beyond the 3 ton electric chain hoist rated weight. Overweight operation will make the motor over heating, overload for a long time will cause irreparable damage to the electric chain hoists for sale.  Electric hoist motor  is not overloaded, but still heating, should check whether the motor bearing damaged; Should also check whether the motor Work according to regulations, which is one of the reasons causing the motor heating. When the electric hoist motor is running, brake clearance is too small, not completely disengaged, causing great friction, while the frictional heating is also equivalent to the additional load

The reason of electrical wire rope hoist does not work after starting

Mainly because of the hoist does not reach to the rated operating voltage, there are generally 3 kinds of situations: 1.Find out whether the power supply system supply power to wire rope electric hoist , generally used test pencil, such as no power supply; 2.The main control circuit of the wire rope electric hoist is damaged, the line is broken or the contact is bad, can also let the hoist motor not be electrified. This situation, need to overhaul the main control circuit. When maintenance, in order to prevent missing phase to burn the motor casused by the main control circuit supply power to three-phase motor, or hoist motor suddenly operate and cause danger, must disconnect electrical wire rope hoist motor from the power supply, only supply power to the main control circuit. Then start and stop switch, check and analyze the working condition of the electric appliance and the line, repair or replace the failed electric appliance or line. When the main control circuit is confirmed

Working level of overhead gantry crane

Overhead gantry crane  installation site and the work conditions is vary greatly, the use of lifting capacity and working frequency are also different. In order to use the crane economically and reasonably, it is necessary to choose the appropriate working level according to the working condition of the crane. The working level of the bridge crane is divided into A1 ~ A8, according to the level of the crane and the load state, that is, according to the frequency and load degree of the crane through the calculation to determine. The crane has a certain number of working cycles during its useful life. A working cycle of a  travelling gantry crane  is to start the process of loading the goods from the beginning to the next. The total number of working cycles represent the utilization of cranes. In order to facilitate the calculation, the total number of working cycles can be divided into 10 categories. 200-400 ton heavy duty travelling  overhead gantry crane for sale